Differences

This shows you the differences between two versions of the page.

--- gecko-systems:gecko3com:installing_windows [2017/03/06 12:20] – external edit 127.0.0.1
+++ gecko-systems:gecko3com:installing_windows [2021/12/20 10:49] (current) – external edit 127.0.0.1
@@ Line 23: / Line 23: @@
 ===== GECKO3COM drivers (Windows only) =====
 This installation is optional. The drivers will suppress the message of ''New Hardware found'' but will not have any use. The drivers are based on the ''libusb-win''.
-{{:huce:microlab:projects:internal:gecko:gecko3:gecko3com:installgecko3comdrivers.zip|}}
+{{gecko-systems:gecko3com:installgecko3comdrivers.zip|}}
 The setup will only copy the drivers to the directory ''C:\Program Files\GECKO3COM\driver''. Therefore choose the next time the ''New Hardware found'' wizard appears the driver in this directory.
@@ Line 33: / Line 33: @@
 The first prompt is the USBTMC. Install  the driver according to the images below.
-{{:huce:microlab:projects:internal:gecko:gecko3:gecko3com:comwininst011.png|}}
+{{:gecko-systems:gecko3com:comwininst011.png|}}
-{{:huce:microlab:projects:internal:gecko:gecko3:gecko3com:comwininst001.png|}}
-{{:huce:microlab:projects:internal:gecko:gecko3:gecko3com:comwininst002.png|}}
-{{:huce:microlab:projects:internal:gecko:gecko3:gecko3com:comwininst003.png|}}
-{{:huce:microlab:projects:internal:gecko:gecko3:gecko3com:comwininst004.png|}}
-{{:huce:microlab:projects:internal:gecko:gecko3:gecko3com:comwininst006.png|}}
+{{:gecko-systems:gecko3com:comwininst001.png|}}
-{{:huce:microlab:projects:internal:gecko:gecko3:gecko3com:comwininst007.png|}}
-{{:huce:microlab:projects:internal:gecko:gecko3:gecko3com:comwininst008.png|}}
+{{:gecko-systems:gecko3com:comwininst002.png|}}
+{{:gecko-systems:gecko3com:comwininst003.png|}}
+{{:gecko-systems:gecko3com:comwininst004.png|}}
+{{:gecko-systems:gecko3com:comwininst006.png|}}
+{{:gecko-systems:gecko3com:comwininst007.png|}}
+{{:gecko-systems:gecko3com:comwininst008.png|}}
 After the installation go to the device manager and check if the USBTMC device has been installed properly. In the third window of the wizard.
-{{:huce:microlab:projects:internal:gecko:gecko3:gecko3com:comwininst005.png|}}
+{{:gecko-systems:gecko3com:comwininst005.png|}}
 ===== GECKO3COM driver =====
@@ Line 54: / Line 60: @@
 This is for both protocols (Command&Status and the Device Firmware Upgrade) the same:
-{{:huce:microlab:projects:internal:gecko:gecko3:gecko3com:comwininst001.png|}}
+{{:gecko-systems:gecko3com:comwininst001.png|}}
-{{:huce:microlab:projects:internal:gecko:gecko3:gecko3com:comwininst102.png|}}
+{{:gecko-systems:gecko3com:comwininst102.png|}}
-{{:huce:microlab:projects:internal:gecko:gecko3:gecko3com:comwininst103.png|}}
+{{:gecko-systems:gecko3com:comwininst103.png|}}
-{{:huce:microlab:projects:internal:gecko:gecko3:gecko3com:comwininst104.png|}}
+{{:gecko-systems:gecko3com:comwininst104.png|}}
 After the installation go to the device manager and check if the Command&Status and the Device Firmware Upgrade device have been installed properly.
-{{:huce:microlab:projects:internal:gecko:gecko3:gecko3com:comwininst101.png|}}
+{{:gecko-systems:gecko3com:comwininst101.png|}}